Introdução geral #
O B002 beacon is equipped with a three-axis acceleration sensor that can detect whether it is in motion. It can switch between two different advertising modes ( Periodic Mode e Autonomous Mode) by changing the Accelerometer Threshold value. It also supports detecting and advertising the battery level. In autonomous mode, it can advertise every 24 hours if it is not moved.

Especificações do produto #
Tabela 1: Especificações do produto
| Protocolo | iBeacon |
| Potência de RF | 0dBm por padrão, -20 a +5dBm Potência TX |
| Distância | Máximo 80m |
| Densidade para rastreamento em ambientes internos | >10m |
| Radiodifusão | Mínimo 100ms |
| Acelerômetro | Opcional |
| Consumo de energia | With acceleration sensor: 5μA @ 5s interval and 0dBm Potência TX |
| Without acceleration sensor: 4.2μA @ 5s interval and 0dBm Potência TX | |
| Bateria | Li-MnO2, 500mAh |
| Peso | 10g |
| Dimensão | 90mm*60mm*1.5mm, Thickness: 1.5~2.5mm.68mm*60mm*2mm, Thickness: 1.5~3.5mm. |
| Certificação | FCCID: 2APPL-100-0B, CE |
Descrição da função #
Estado Ligado/Desligado #
- Turn on: Press the button for 3s and the red light flashes for one minute.
- Turn off: Press the button for 3s and no light flashes.

TX Power #
A intensidade do sinal enviado pelo beacon. O valor padrão é 06 (0dBm).
Tabela 2: TX Power
| Tipo de valor | Valor | TX Power (dBm) |
| Hex | 01 | -20 |
| 02 | -16 | |
| 03 | -12 | |
| 04 | -8 | |
| 05 | -4 | |
| 06 | 0 | |
| 07 | 4 |
Intervalo de anúncios #
O intervalo de anúncio do beacon é de 5 segundos por padrão, o que significa que o beacon anuncia o pacote de publicidade uma vez a cada 5 segundos. O intervalo máximo de anúncio é de 10 segundos.
Tabela 3: Intervalo de Publicidade
| Tipo de valor | Valor | Iintervalo (ms) |
| Hex | 01000000 | 100 |
| 02000000 | 200 | |
| 03000000 | 300 | |
| 04000000 | 400 | |
| 05000000 | 500 | |
| …… | …… | |
| 64000000 | 10,000 |
Accelerometer Threshold #
The Accelerometer threshold value is 0x00 by default which means that autonomous mode is disabled and the beacon advertises in the Periodic Mode. When the Accelerometer threshold value is greater than or equal to 0x10, the beacon advertises in the Autonomous Mode. The beacon is considered in motion when the accelerated speed is larger than the threshold. The default unit is 16mg, Accelerometer threshold = value * 16mg.
Table 4: Accelerometer Threshold
| Tipo de valor | Valor | Threshold (mg) |
| Hex | 00 | 00 means the periodic mode is enabled. |
| 01 ~ 0F | Reserved for future use. | |
| 10 | 256 (0x10 = 16, 16x16mg = 256mg)Autonomous Mode | |
| 11 | 272(0x11 = 17, 17x16mg = 272mg) | |
| 12 | 288 | |
| 13 | 304 | |
| …… | …… | |
| 7F | 2032 |
Advertise Mode #
Periodic Mode #
In the periodic mode, the beacon advertises the advertising packet at fixed intervals as configured until the battery power runs out.
Autonomous Mode #
In the autonomous mode, the beacon only advertises when it is in motion. When the acceleration is larger than the Accelerometer threshold, the beacon advertises with the Advertise Interval value for the duration of the Advert Time.
For example, if the interval value is 5s and the advert time is 1min, the beacon will not advertise if it is stationary. When the acceleration is larger than the Accelerometer threshold, the beacon will advertise once every 5s and keep advertising for 1min.
Advert Time #
The duration of the beacon advertisement is 0000 by default, and the maximum advertise time is 65535s. This configuration only works in autonomous mode. If the beacon works in periodic mode, this configuration has no effect.
Table 5: Advert Time
| Tipo de valor | Valor | Time (s) |
| Hex | 0000 | Broadcast all the time. |
| 0001 ~ 001D | Reserved for future use. | |
| 001E | 30 | |
| 001F | 31 | |
| 0020 | 32 | |
| …… | …… | |
| FFFF | 65535 |
Configuração do interruptor #
O B002 beacon has two switch functions: “Battery Level Advert” and “No Movement 24h Advert”. The “Battery Level Advert” function determines whether the beacon advertises with the battery level. The “No Movement 24h Advert” function determines whether the beacon advertises every 24 hours if it is not moved.
Table 6: Switch Configuration
| Name | Valor | Ddescrição |
| Anúncio do nível da bateria | 00:disabled, 01:enabled,the default value is 0. | This configuration determines whether the beacon advertises the battery level. |
| No Movement 24h Advert | 00:disabled, 01:enabled,the default value is 0. | This configuration only works in autonomous mode, where the beacon advertises every 24 hours if it is not moved.In periodic mode, this configuration has no effect. |
Recurso publicitário #
Em Periodic Mode, the beacon advertises a 30-byte packet with a fixed 5s Intervalo de anúncios. In Autonomous Mode, the beacon only advertises with the advertise interval value for the duration of the Advert Time when it is in motion and will not advertise when it is stationary.
The beacon advertising packet is as follows.
Pacote padrão de publicidade #
O sinalizador emite um pacote de publicidade padrão quando o recurso de nível de bateria não está ativado.
Table 7. Standard iBeacon Advertising Packet
| Deslocamento de byte | Valor padrão | Descrição | Propriedades |
| 0 | 0x02 | Comprimento dos dados – 2 bytes | Preâmbulo constante |
| 1 | 0x01 | Tipo de dados – sinalizadores | Preâmbulo constante |
| 2 | 0x06 | Bandeira LE e BR/EDR | Preâmbulo constante |
| 3 | 0x1A | Comprimento dos dados – 26 bytes | Preâmbulo constante |
| 4 | 0xFF | Tipo de dados – Dados específicos do fabricante | Preâmbulo constante |
| 5 | 0x4C | Dados do fabricante | Preâmbulo constante |
| 6 | 0x00 | Dados do fabricante | Preâmbulo constante |
| 7 | 0x02 | Dados do fabricante | Preâmbulo constante |
| 8 | 0x15 | Dados do fabricante | Preâmbulo constante |
| 9 | 0xF2 | Primeiro byte do UUID de proximidade | UUID do usuário |
| 10 | 0xA5 | UUID de proximidade (2º byte) | UUID do usuário |
| 11 | 0x2D | UUID de proximidade (3º byte) | UUID do usuário |
| 12 | 0x43 | UUID de proximidade (4º byte) | UUID do usuário |
| 13 | 0xE0 | UUID de proximidade (5º byte) | UUID do usuário |
| 14 | 0xAB | UUID de proximidade (6º byte) | UUID do usuário |
| 15 | 0x48 | UUID de proximidade (7º byte) | UUID do usuário |
| 16 | 0x9C | UUID de proximidade (8º byte) | UUID do usuário |
| 17 | 0xB6 | UUID de proximidade (9º byte) | UUID do usuário |
| 18 | 0x4C | UUID de proximidade (10º byte) | UUID do usuário |
| 19 | 0x4A | 11º byte do UUID de proximidade | UUID do usuário |
| 20 | 0x83 | UUID de proximidade (12º byte) | UUID do usuário |
| 21 | 0x00 | UUID de proximidade (13º byte) | UUID do usuário |
| 22 | 0x14 | UUID de proximidade (14º byte) | UUID do usuário |
| 23 | 0x67 | UUID de proximidade (15º byte) | UUID do usuário |
| 24 | 0x20 | UUID de proximidade (16º byte) | UUID do usuário |
| 25 | AA | Primeiro byte principal | Valor principal |
| 26 | BB | Segundo byte principal | Valor principal |
| 27 | CC | Primeiro byte menor | Valor menor |
| 28 | CC | Segundo byte menor | Valor menor |
| 29 | 0xB3 | Potência do sinal (SSI calibrado a 1 m) | Valor da potência do sinal |
Pacote publicitário com indicador de nível de bateria #
O beacon também suporta a exibição de informações sobre o nível da bateria no último byte. Capítulo 5.2 Configuração do anúncio do nível da bateria Explica como ativar esse recurso por meio do “LightBlue”.
Table 8: Advertising Packet with Battery Level
| Deslocamento de byte | Valor padrão | Descrição | Propriedades |
| 0 | 0x02 | Comprimento dos dados – 2 bytes | Preâmbulo constante |
| 1 | 0x01 | Tipo de dados – sinalizadores | Preâmbulo constante |
| 2 | 0x06 | Bandeira LE e BR/EDR | Preâmbulo constante |
| 3 | 0x1B | Comprimento dos dados – 27 bytes | Preâmbulo constante |
| 4 | 0xFF | Tipo de dados – Dados específicos do fabricante | Preâmbulo constante |
| 5 | 0x4C | Dados do fabricante | Preâmbulo constante |
| 6 | 0x00 | Dados do fabricante | Preâmbulo constante |
| 7 | 0x02 | Dados do fabricante | Preâmbulo constante |
| 8 | 0x15 | Dados do fabricante | Preâmbulo constante |
| 9 | 0xF2 | Primeiro byte do UUID de proximidade | UUID do usuário |
| 10 | 0xA5 | UUID de proximidade (2º byte) | UUID do usuário |
| 11 | 0x2D | UUID de proximidade (3º byte) | UUID do usuário |
| 12 | 0x43 | UUID de proximidade (4º byte) | UUID do usuário |
| 13 | 0xE0 | UUID de proximidade (5º byte) | UUID do usuário |
| 14 | 0xAB | UUID de proximidade (6º byte) | UUID do usuário |
| 15 | 0x48 | UUID de proximidade (7º byte) | UUID do usuário |
| 16 | 0x9C | UUID de proximidade (8º byte) | UUID do usuário |
| 17 | 0xB6 | UUID de proximidade (9º byte) | UUID do usuário |
| 18 | 0x4C | UUID de proximidade (10º byte) | UUID do usuário |
| 19 | 0x4A | 11º byte do UUID de proximidade | UUID do usuário |
| 20 | 0x83 | UUID de proximidade (12º byte) | UUID do usuário |
| 21 | 0x00 | UUID de proximidade (13º byte) | UUID do usuário |
| 22 | 0x14 | UUID de proximidade (14º byte) | UUID do usuário |
| 23 | 0x67 | UUID de proximidade (15º byte) | UUID do usuário |
| 24 | 0x20 | UUID de proximidade (16º byte) | UUID do usuário |
| 25 | AA | Primeiro byte principal | Valor principal |
| 26 | BB | Segundo byte principal | Valor principal |
| 27 | CC | Primeiro byte menor | Valor menor |
| 28 | CC | Segundo byte menor | Valor menor |
| 29 | 0xB3 | Potência do sinal (SSI calibrado a 1 m) | Valor da potência do sinal |
| 30 | Nível da bateria | Bnível da bateria | Bnível da bateria |
Configurando o Lansitec BLE Beacon com um iPhone #
Observação: todos os parâmetros estão em codificação hexadecimal.
Passo 1: Procure e baixe o aplicativo “LightBlue” na App Store.

Etapa 2: Pressione e segure o botão para ligá-lo. B002 beacon label. A red light flashes in the first minute.
Etapa 3: Abrir Azul claro, and click a beacon with the name “LS_Beacon_Vx.x” which will show up in the app. Please click the iBeacon within 1 minute after powering on, or it must be restarted to enter the configuration mode again.
![]()
Configuração principal #


- Clique em “Principal” (passo 1).
- Clique em “Escrever novo valor” (passo 2).
- Enter a new value (step 3) and click “Done” (step 4) to save and click “0xFFF2” (step 5) to return to the “Major” page.
- The new value is shown in the value block (step 6) of the “Major” page, and the previous value is grey. Click the “LS_Beacon_V8.3” (step 7) to return to the previous page.
- Clique em “Voltar” (passo 8) para sair da configuração. Caso contrário, a alteração NÃO será salva.
Configure “UUID”, “Minor”, “Interval”, “TX_power”, “Accelerometer thld”, and “Advert time” in the same way. Please exit LightBlue after configuration. The light stops flashing after configuration.
Configuração do anúncio do nível da bateria #


- Clique em “Anúncio do nível da bateria” (passo 1).
- Clique em “Escrever novo valor” (passo 2).
- Enter value “00” means disable the battery level advertising function, and “01” means enable this function (step 3). Click “Done” (step 4) to save and click “0xFFF8” (step 5) to return to the “Battery Level Advert” page.
- O novo valor é exibido no bloco de valores (etapa 6) da página “Anúncio do nível da bateria”, e o valor anterior aparece em cinza.
- Click the ” LS_Beacon_V8.3″ (step 7) to return to the previous page. Then exit the configuration. Otherwise, the change will NOT be saved.
Configure “No Movement 24h Advert” in the same way. Please exit LightBlue after configuration. The light stops flashing after configuration.
We can also preprogram the “UUID”, “Major”, “Minor”, “Interval”, “TX_power”, “Accelerometer thld”, “Advert time”, “Battery Level Advert”, and “No Movement 24h Advert” for you and print it on housing before shipment.
Battery Life B002 Bluetooth Beacon Label #
Table 9: Battery Life (with the Acceleration Sensor)
| Intervalo de transmissão (ms) | 100 | 500 | 1000 | 5000 |
| Corrente média (μA) | 154 | 33.8 | 17 | 5 |
| Duração da bateria (meses) | 3 | 15 | 29 | 104 |
Table 10: Battery Life (without the Acceleration Sensor)
| Intervalo de transmissão (ms) | 100 | 500 | 1000 | 5000 |
| Corrente média (μA) | 153 | 33 | 16 | 4.2 |
| Duração da bateria (meses) | 3 | 15 | 31 | 124 |
Note:
Em relação à precisão, diversos fatores influenciam a exatidão das medições de distância com BLE. RSSI.
- Shadow effect: signals can be reflected by walls and glasses around many times during the transmission. Diffraction changes the signal path This results in receiving unstable signal strength.
- Existem muitos dispositivos conectados às redes 2.4G, Wi-Fi, Bluetooth e Zigbee. Os sinais podem se sobrepor, tornando a intensidade do sinal recebido instável.
- Devido às limitações na fabricação de semicondutores, Potência TX Não é estável.
Ao usar um beacon para posicionamento, considere o seguinte método para medir a distância.
- Enquanto o farol estiver anunciando, experimente repetidamente o RSSI a uma distância de 1 metro por um mínimo de 10 segundos.
- Descartar os 10% mais altos. RSSI amostras.
- Descarte os 20% mais baixos. RSSI amostras.
- Calcule a média das amostras restantes para obter o valor de Potência Medida.
Recomendamos outros dois algoritmos para calcular a distância e a posição:
- Algoritmo de média móvel, documento Lansitec número 930-00171.
- Calibração de posição, documento Lansitec número 930-00172.
How to Install a B002 Bluetooth Beacon Label #

Tear the back double-sided adhesive tape and stick it to anywhere you want.

Embalagem #
Embalagem em lote

Embalagem de amostra

Informações para encomenda #
| Descrição | PN |
| BLE label, ibeacon, 320mAh | 100-0B002 |